Showing results: 976 - 990 of 2617 items found.
-
Newport Electronics
High speed optical detectors use special photodiodes with high speed electronic circuits to convert fast optical pulses to electrical signals for measurement. Unlike our optical receivers, these detectors do not include a transimpedance amplifier.
-
LFG-50 -
Kharkovenergopribor Ltd.
• tracing – finding the route and determining the burial depth of underground cables and other hidden utilities;• fault location – pinpointing interphase and phase-to-sheath short circuits faults;• cable identification – identifying a correct cable from a bunch.
-
4380 -
Dwyer Instruments Inc.
The Iso Verter II Isolator/Converter protects electronic circuits by completely isolating the input and output signals from each other and from ground. Both input and output ranges are fully field selectable with easy to adjust switches
-
Earth-Rite OMEGA II -
Newson Gale Inc.
The Earth-Rite OMEGA II monitors the resistance of the static grounding circuit for processes where a risk of static charge accumulation on the equipment could result in an incendive electrostatic spark within locations that have potentially flammable atmospheres present.
-
EKMB (WL) Series -
Panasonic Industrial Devices Sales Company of America
Panasonic EKMB Series PIR Motion Sensors are suitable for low current consumption for battery-driven applications. Reduces current consumption (1, 2, or 6μA) with featured special circuit design technology allowing longer battery life.
-
MDLA-100 -
MULTI MEASURING INSTRUMENTS Co., Ltd.
This DC Leakage Current Monitor constantly observes leakage current of DC circuit like as PV generation system, etc. and lights up the warning lamp with signal output, when the leakage current exceeds the setting value.
-
MHR-600 -
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Measuring and recording the average current values & power flow directions in the setting interval.・Easy to use, as an indirect hot-line work tool.・Memorized data can be outputted to USB memoryafter measurement.・For 6.6KV circuit, protection level IP64.
-
Leuze electronic GmbH + Co. KG
With the MSI safety relays, individual safety sensors can be integrated quickly and easily into the safety circuit of machines and systems. The MSI contact extensions are used both as an output extension for OSSDs and for contact multiplication for evaluation units and safety controls.
-
LCR01D -
MINPU TECHNOLOGY CO., LTD.
*Basic accuracy:0.3%*Test Voltage: 0.5Vrms* Circuit Calibration:Open/Short*Test Frequency:10MHz,5MHz,1MHz,100KHz,10KHz,1KHz*Measure Parameters Include:Z, Lp, Ls, Cp, Cs, ESR, D, Q, θ
-
MegiQ BV
The unbalanced interface of a VNA is not very well suited for measuring balanced circuits like antennas, transmission lines or chip impedances. In fact it is nearly impossible to get a decent calibration on a balanced 2-port measurement using coax cables.
-
PinPoint II R -
DiagnoSYS Systems Ltd
The Diagnosys PinPoint IIR provides industry-leading capability for the test and fault finding of the most challenging PCB (or CCAs). Allowing you to select and apply different test techniques on a single circuit, you can ensure maximum fault coverage.
-
Applied Relay Testing Ltd.
General purpose calibration/diagnostic tool.Built in precision resistors.Simple manual contact/routing/resistor selection.4mm terminal posts on key device connections.In line mode to aid fixture wiring/DUT debugging.Comprehensive documentation including circuit schematics.Connecting cables.
-
National Technical Systems
Conductive Anodic Filament (CAF) testing helps to determine the reliability of a printed circuit board (PCB) laminate material or a finished product. With conductor spacing and overall part sizes getting smaller and smaller, the necessity for this test is increasing.
-
HW Test
H+W Test Products has developed a series of inexpensive mechanical test fixtures. These fixtures are designed for testing low volume runs of printed circuit boards or prototype applications requiring approximately 150 test points.
-
CCM1095 and CCM2096 -
Teledyne RF & Microwave
The CCM1095 and CCM2096 are power amplifiers that use current efficient Silicon Carbide output semi-conductors to achieve +35 to +38 dBm output power. An internal sequencing circuit is included to provide for safe operation of the output power device.